LAPLINK SERIAL CABLE 컴컴컴컴컴컴컴컴컴� THIS IS A FOUR ENDED CABLE. EACH OF THE TWO ENDS HAS A DB9 FEMALE AND A DB 25 FEMALE CONNECTOR.(SERIAL PORTS ON COMPUTERS AR EITHER DB-9 MALE OR DB-25 MALE. THIS WAY THE CABLE CAN BE USED TO CONNECT TO EITHER AT'S OR XT OR TO CONNECT BETWEEN. THIS IS THE INFORMATION OBTAINED WHEN USING A VOLT-OHM-METER TO "BUZZ OUT" THE ORIGINAL CABLE. 컴컴컴컴컴컴컴컴� DB9 FEMALE \ 5 4 3 2 1 / \ 9 8 8 6 / MATING SIDES OF CONNECTORS 컴컴컴컴컴컴� DB25 FEMALE 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� \13 12 11 10 9 8 7 6 5 4 3 2 1/ \ 25 24 23 22 21 20 19 18 17 16 15 14/ 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴� DB9컴컴� "A" "B" 旼컴컴DB9 쳐컴컴컴컴컴컴컴컴컴컴컴컴컴� � CONSTRUCTION OF CABLE � DB25컴켸 ABOUT TEN FEET LONG 읕컴컴DB25 OBVIOUSLY IF YOU DONT NEED BOTH ENDS DON'T MAKE THEM DB9 "A" DB9 "B" DB25 "A" DB25 "B" 2 3 3 2 3 2 2 3 4 6 20 6 5 5 7 7 6 4 6 20 7 8 4 5 8 7 5 4 THE FOLLOWING IS FROM THE LAPLINK DOCUMENTATION 컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴컴 If you are going to have a cable custom built, use the following pin-out requirements to build a 3-wire serial cable. It can be built either with both a 9 and a 25 pin connector on each end, or just one connector at each end. Four possible combinations are shown below. Note that you may have to start LapLink III with the 3-wire command line switch with a 3-wire cable. If LapLink III does not connect when running on both computers, exit the program on both computers and re-start LapLink on both by typing on the command line: LL3 /3 DB9F and DB25F to DB25F and DB9F 2 컴컴컴 3 컴컴컴컴컴컴컴컴 2 컴컴컴� 3 3 컴컴컴 2 컴컴컴컴컴컴컴컴 3 컴컴컴� 2 5 컴컴컴 7 컴컴컴컴컴컴컴컴 7 컴컴컴� 5 DB25F to DB25F FROM DVORAK'S 2 컴컴컴컴컴컴컴컴 3 NULL MODEM CABLE 3 컴컴컴컴컴컴컴컴 2 DB-9 TO DB-25 7 컴컴컴컴컴컴컴컴 7 旼1컴컴컴N.C. DB9F to DB25F � 2컴컴컴2 2 컴컴컴컴컴컴컴컴 2 � 3컴컴컴3 3 컴컴컴컴컴컴컴컴 3 � 4컴컴컴6,8 5 컴컴컴컴컴컴컴컴 7 � 5컴컴컴7 읕6컴컴컴20 DB9F to DB9F 7컴컴컴5 2 컴컴컴컴컴컴컴컴 3 8컴컴컴4 3 컴컴컴컴컴컴컴컴 2 9컴컴컴NC 5 컴컴컴컴컴컴컴컴 5